Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
For details on the location of the front (and rear) speakers, see “Location of each speaker” on this page. 1 Detach the plate from the stand. 2 Pass the speaker cord into the hole on the back of the stand and out from the hole at the center of the stand. continued 7GB Positioning the speakers (continued) 3 Separate the speaker cord, then secure the cord to the speaker stand with the plate. 4 Connect the speaker cord to the speaker terminal. The cord should be pressed into the groove in the stand. 5 Using the supplied hex wrench, two screws, and washers, secure the speaker to the stand. Positioning the center speaker (SA-VE705 only) Attach the center speaker to the supplied speaker stand and place it on a top of the TV set. For optimum listening enjoyment, the speaker should face directly towards the listener. Adjust the angle of the speaker stand for that purpose. 1 Pass the speaker cord into the hole on the back of the stand and out from the hole at the center of the stand. 2 Connect the speaker cord to the speaker terminal. Notes • Do not remove the supplied speaker grille from the speaker while attaching the speaker to the speaker stand. • Do not touch or press tweeter’s cover on the center of the speaker. 8GB 3 Using the supplied hex wrench, two Listening to the sound screws, and washers, secure the speaker to the stand. Operation panel on the subwoofer Notes • Do not remove the supplied speaker grille from the speaker while attaching the speaker to the speaker stand. • Do not touch or press tweeter’s cover on the center of the speaker. 4 Adjust the angle of the speaker stand. Loosen the two screws under the base to adjust the angle. Then tighten them again afterwards. 15. 25. Screws The optional speaker stands For greater flexibility in the positioning of the speakers, use the optional WS-FV10 (floor stand), WS-TV10 (TV stand), or WS-WV10 (wall mount bracket) speaker stand (available only in certain countries). LEVEL MODE MIN ON/ STANDBY MAX MOVIE MUSIC! ON/STANDBY ! indicator First, turn down the volume on the amplifier. The volume should be set to minimum before you begin playing the program source. 1 Turn on the amplifier and select the program source. 2 Press ! on the subwoofer. The ON/STANDBY indicator on the subwoofer lights up green. 3 Play the program source. Power turns on and off automatically — Auto power on/off function When the subwoofer is on (i.e, the ON/STANDBY indicator lights up green) and there is no signal input for a few minutes, the ON/STANDBY indicator changes to red and the subwoofer enters power saving mode. While in this mode a signal is input to the subwoofer, the subwoofer automatically turns on (auto power on/off function). To turn this feature off, slide the POWER SAVE switch on the rear panel to OFF. AUTO OFF POWER SAVE Note If you turn down the volume level of the subwoofer too low, the auto power on/off function may activate, causing the subwoofer to enter power saving mode. WS-FV10 WS-TV10 WS-WV10 9GB Adjusting the sound Slight adjustments to the system can enhance your sound enjoyment. Adjusting the subwoofer Operation panel on the subwoofer LEVEL MODE MIN ON/ STANDBY MAX MOVIE MUSIC! LEVEL MODE 1 Set MODE according to the program source as follows: Setting your amplifier to enjoy movies (SA-VE705 only) For the Dolby Digital (AC-3) If your amplifier is connected internally or externally with a Dolby Digital (AC-3) processor, you should use the some setup menus in the amplifier to specify the parameters of your speaker system. See the table below for the proper settings. For details on the setting procedure, refer to the manual that was provided with your amplifier. When “Hookup A” is used (Speaker setup menu) For Set to Front speakers SMALL Source MODE Center speaker SMALL DVD, LD, video cassette MOVIE Rear speakers SMALL or other video source Subwoofer ON (or YES) MD, CD, cassette tape MUSIC or other audio source (Other setup menu) 2 Rotate LEVEL to adjust the volume. Set the volume level to suit the program source. Notes • Some amplifier functions for enhancing the sound may cause distortion in the subwoofer. If such distortion occurs, turn off those functions. • To enjoy high-quality sound, do not turn the subwoofer volume too high. • To increase the bass sound from the subwoofer, connect the system using “Hookup B” (see page 5). Menu Set to LFE* MIX –10 dB BASS BOOST** ON * Low Frequency Effect **A function that reinforces the bass sound When “Hookup B” is used (Speaker setup menu) For Set to Front speakers LARGE Center speaker SMALL Rear speakers SMALL Subwoofer OFF (or NO) (Other setup menu) Menu Set to LFE MIX –10 dB BASS BOOST ON 10GB Precautions On safety • Before operating the system, be sure that the operating voltage of the system is identical with that of your local power supply. • The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. • Unplug the system fr...
Эта инструкция также подходит к моделям:Акустика - SA-VE705 (237.73 kb)