Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Adjust the angle of the speaker stand for that purpose. 1 Pass the speaker cord into the hole on the back of the stand and out from the hole at the center of the stand. 2 Connect the speaker cord to the speaker terminal. 3 Using the supplied screw and washer, secure the speaker to the stand. Note Do not remove the supplied speaker grille from the speaker while attaching the speaker to the speaker stand. 4 Adjust the angle of the speaker stand. Loosen the two screws under the base to adjust the angle. Then tighten them again afterwards. Setting the speakers To prevent speaker vibration or movement while listening, attach the supplied foot pads to the front speakers and rear speakers (E). The optional speaker stands (F) For greater flexibility in the positioning of the speakers, use the optional WS-FV10C (floor stand), WS-TV10C (TV stand), or WS-WV10C (wall mount bracket) speaker stand (available only in certain countries). Tip The height of the front speakers should be adjusted to about the center of the TV screen (G). Setting the amplifier When connecting to an amplifier with internal decoders (Dolby Digital, DTS**, etc.), you should use the setup menus for the amplifier to specify the parameters of your speaker system. See the table below for the proper settings. For details on the setting procedure, refer to the manual that was provided with your amplifier. Select Micro Satellite Position if a Sony amplifier provides it. Speaker setup For Set to Front speakers SMALL Center speaker SMALL Rear speakers SMALL Subwoofer ON (or YES) ** “DTS” and “DTS Digital Surround” are registered trademarks of Digital Theater Systems, Inc. Listening to the sound (H) First, turn down the volume on the amplifier. The volume should be set to minimum before you begin playing the program source. 1 Turn on the amplifier and select the program source. 2 Press POWER on the subwoofer. The ON/STANDBY indicator on the subwoofer lights up green. 3 Play the program source. Power turns on and off automatically — Auto power on/off function (I) When the subwoofer is on (i.e, the ON/STANDBY indicator lights up green) and there is no signal input for a few minutes, the ON/STANDBY indicator changes to red and the subwoofer enters power saving mode. While in this mode a signal is input to the subwoofer, the subwoofer automatically turns on (auto power on/off function). To turn this feature off, slide the POWER SAVE switch on the rear panel to OFF. Note If you turn down the volume level of the amplifier too low, the auto power on/off function may activate, causing the subwoofer to enter power saving mode. Adjusting the subwoofer (H) 1 Set MODE according to the program source as follows: Source MODE DVD, LD, video cassette MOVIE or other video source MD, CD, cassette tape MUSIC or other audio source 2 Rotate LEVEL to adjust the volume. Set the volume level to best suit your preference according to the program source. Notes • Some amplifier functions for enhancing the sound may cause distortion in the subwoofer. If such distortion occurs, turn off those functions. • To enjoy high-quality sound, do not turn the subwoofer volume too high. • The bass sound is enhanced in MOVIE mode rather than in MUSIC mode. Therefore, if you change the mode to MOVIE while listening to some sources that do not include the bass sound, you may not be able to get the effect. Troubleshooting Should you encounter a problem with your speaker system, check the following list and take the indicated measures. If the problem persists, consult your nearest Sony dealer. There is no sound from the speaker system. • Make sure all the connections have been correctly made. • Make sure the volume on the amplifier has been turned up properly. • Make sure the program source selector on the amplifier is set to the proper source. • Check if headphones are connected. If they are, disconnect them. There is distortion in the subwoofer sound output. • Check if any sound-enhancing functions have been activated on the amplifier. If they have, turn them off. There is hum or noise in the speaker output. • Make sure all the connections have been correctly made. • Make sure none of the audio components are positioned too close to the TV set. The sound has suddenly stopped. • Make sure all the connections have been correctly made. Contact between bare speaker wires at the speaker terminals may cause a short-circuit. Specifications SS-MS535 (front, center, and rear speakers) Speaker system 2 way, magnetically shielded Speaker units Woofer: 5.7 cm, cone type Tweeter: 2.5 cm, balance dome type Enclosure type Bass reflex Rated impedance 8 ohms Power handling capacity Maximum input power: 120 watts Sensitivity level 85 dB (1 W, 1 m) Frequency range 120 Hz - 50,000 Hz Dimensions (w/h/d) When attached speaker grille: Approx. 98 . 168 . 137 mm When attached supplied speaker stand: Approx. 168 . 135 . 150 mm (pointed upwards) Approx. 168 . 127 . 150 mm (pointed downwards) Mass When attached speaker grille:...