Оценок - 2, средний балл: 4.5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
Tip All striped wires are minus (–) in polarity, and should be connected to the minus (–) speaker terminals. Positioning the speakers Location of each speaker (C) Each speaker should face the listening position. Better surround effect will result if all speakers are set at the same distance from the listening position. Place the front speakers at a suitable distance to the left and right of the television. Place the subwoofer on either side of the television. Place the center speaker on the top-center of the TV set. The placement of surround speakers greatly depends on the configuration of the room. The surround speakers may be placed on both sides of the listening position A or behind the listening position B. Tips • Movies are best enjoyed in a room that produces no echoes (as in one with surrounding curtains). • Music (especially classical music) is best enjoyed in a room that produces some echo. . 2003 Sony Corporation Printed in Malaysia D G H E F Foot pads POWER LEVEL MIN MAX POWER LEVEL WS-WV10D (for surround speaker) Foot pads WS-FV10D Micro Satellite System SA-VE2M POWER indicator Setting the speakers Attaching the speaker pads (D) To prevent speaker vibration or movement while listening, attach the supplied foot pads to the bottom four corners of the center speaker, front speakers, and surround speakers. Setting the center speaker (E) Set the center speaker firmly on top of the TV set. Make sure it is completely level. Setting other speakers (F) For greater flexibility in the positioning of the speakers, use the optional WS-FV10D or WS-WV10D speaker stand (available only in certain countries). Tip (G) The height of the front speakers should be adjusted to about the center of the TV screen. Setting the amplifier When connecting to an amplifier with internal multi channel decoders (Dolby Digital, DTS**, etc.), you should use the setup menus for the amplifier to specify the parameters of your speaker system. See the table below for the proper settings. For details on the setting procedure, refer to the manual that was provided with your amplifier. Speaker setup For Set to Front speakers SMALL Center speaker SMALL Surround speakers SMALL Subwoofer ON (or YES) If you use the amplifier with adjustable crossover frequency, it is recommended to select 120 Hz (or close to this figure) as the crossover frequency for your front, center, and surround speakers. ** “DTS” and “DTS Digital Surround” are registered trademarks of Digital Theater Systems, Inc. Listening to the sound (H) First, turn down the volume on the amplifier. The volume should be set to minimum before you start playing the program source. 1 Turn on the amplifier and select the program source. 2 Press POWER on the subwoofer. The POWER indicator on the subwoofer lights up green. 3 Play the program source. Adjusting the subwoofer (H) Rotate LEVEL to adjust the volume. Set the volume level to best suit your preference according to the program source. Notes • Some amplifier functions for enhancing the sound may cause distortion in the subwoofer. If such distortion occurs, turn off those functions. • To enjoy high-quality sound, do not turn the subwoofer volume too high. For the Dolby Pro Logic If your amplifier is connected internally or externally with a Dolby Pro Logic processor, you should set the surround effect mode to “NORMAL” on the amplifier for your particular speaker system. For details on the setting procedure, refer to the manual that was provided with your amplifier. Troubleshooting Should you encounter a problem with your speaker system, check the following list and take the indicated measures. If the problem persists, consult your nearest Sony dealer. There is no sound from the speaker system. •Make sure all the connections have been correctly made. •Make sure the volume on the amplifier has been turned up properly. •Make sure the program source selector on the amplifier is set to the proper source. •Check if headphones are connected. If they are, disconnect them. There is distortion in the subwoofer sound output. •Check if any sound-enhancing functions have been activated on the amplifier. If they have, turn them off. There is hum or noise in the speaker output. •Make sure all the connections have been correctly made. •Make sure none of the audio components are positioned too close to the TV set. The sound has suddenly stopped. •Make sure all the connections have been correctly made. Contact between bare speaker wires at the speaker terminals may cause a short-circuit. Specifications SS-MS2M (Front and surround speakers) Speaker system Full range, magnetically shielded Speaker units 8 cm, cone type Enclosure type Bass reflex Rated impedance 8 ohms Power handling capacity Maximum input power: 100 watts Sensitivity level 86 dB (1 W, 1 m) Frequency range 28 Hz - 20,000 Hz Dimensions (w/h/d) Approx. 105 . 153 . 127 mm, including front grille Mass Approx. 1.2 kg each SS-CN2M (Center speaker) Speaker system Full range , magnetically shiel...