Оценок - , средний балл:
(
)
)
Производитель: Atlas Sound
Размер: 762.55 kb
Название файла:
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
INSERT AND TIGHTEN BASE SLEEVE SCREW TO DOUBLE LOCK SPEAKER TO BASE. Specifications are subject to change without notice 1601 JACK MCKAY BOULEVARD ENNIS, TEXAS 75119 U.S.A. • TELEPHONE: (800) 876-3333 • FAX: (800) 765-3435 © 2003 ATLAS SOUND LP Printed in U.S.A. 00803 ATS000706 RevC 8/03 PN 416689 eliminate the possibility of injury or property damage. WALL MOUNT Attach base directly to wall via (4) holes provided in base using screws provided or suitable strength fasteners. STRAP OR CLAMP MOUNT TO A POLE OR BEAM Attach base directly to pole or beam via a 1.2" hose clamp or suitable banding strap. A beam clamp may also be utilized with the APX base. Make sure that the strap, banding or clamp is correct for the application environment. SINGLE GANG, TWO GANG OR 4" SQ. E.O. BOX MOUNT Using a box screw (#6) or a nail, align center 2 knock out holes (4 on 2 gang) in base and knock out holes with hammer. Pull speaker wire through rubber grommet in base. Attach base through 2 center knocked out holes (4 outer holes on 2 gang box). EXTERIOR BOX WITH FLEXIBLE CONDUIT Using a hammer and a box screw (#6) or a nail, knock out holes in base. Knock out 1.2" K.O. in base plus the back cap with hammer and screwdriver or pliers. Attach BX adapters and flex conduit to base and backcap. Place gasket on box (not provided). Pull speaker wire through box gasket, base and flex conduit. FLUSH/BULKHEAD STYLE MOUNTING Cutout size of the loudspeaker is 131.8" x 85.8" K.O.'s are 1.4" holes. NOTE! In retrofit applications, if you are replacing Atlas Sound AP Series speakers, you may use the existing AP bracket for the APX Series. Simply unscrew wing nut on the APX to remove base and mount to AP bracket. (if color match AP base is desired, order XS8200601) 3. TO SET POWER TAPS, ROTATE SWITCH WITH FLAT BLADE SCREWDRIVER TO DESIRED POWER OR IMPEDANCE. NOTE! To remove speaker from snap-lock- base sleeve, first remove base sleeve screw. Then insert screwdriver in opening under sleeve and gently pry snap lock up to remove base sleeve. 5. FEED HOOK UP WIRES TO UNIT AND WRAPAROUND CAP SCREWPOSTS AND/OR THE WIRE BARRIER BRACKET FOR STRAIN-RELIEF. 6. ATTACH WIRE TO SCREW TERMI- NALS AND SECURE CAP WITH TWO PARTIALLY CAPTIVE SCREWS. THIS STEP "TRIPLE LOCKS" THE LOUDSPEAKER TO THE BASE. NOTE! For wiring adjustments, back-out the right screw on the security cap more than the left screw to provide swing-open access! 7. AIM HORN IN THE APPROPRIATE DIRECTION AND LOCK INTO PLACE BY TIGHTENING WINGNUT ON BASE ASSEMBLY. 8. ROTATE BELL (if needed) Loosen the tip assembly in horn bell by turning 1.2 turn counter clockwise, rotate bell to position (in 15° increments) and lock back in place by turning tip back 1.2 turn clockwise. WIRE SLOT NOTE: that slot may be enlarged using needle-nosed pliers. 60° 40° ...
Эта инструкция также подходит к моделям:Акустика - APX40TN (762.55 kb)