Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
In this configuration the amplifier sums the right and left channel to deliver one channel (mono) output. Please note: in order for the amplifier to sum right and left signal information, both right and left RCA connections must be made. **CAUTION! In the bridged mode, the amplifier must see the recommended minimum impedance or higher. Any lower than the recommended minimum impedance will cause the amplifier to overheat and possibly cause permanent damage to the amplifier! ELA465 BRIDGED SPEAKER CONNECTIONS ENGLISH ELA AMPLIFIERS FUSE 25A SPEAKERS BRIDGED +12V PROTECT POWER REM GND LEFT RIGHT + - 8 Ohm (4 Ohm Minimum) BRI BRI FUSES 25A 25A SPEAKERS PROTECT POWER +12V REM GND CH1 CH3 CH2 CH4 8 Ohm (4 Ohm Minimum) ELA265, ELA2100 & ELA2150 BRIDGED SPEAKER CONNECTIONS FUSE 25A SPEAKERS BRIDGED +12V PROTECT POWER REM GND LEFT RIGHT 13 CAUTION! In Tri- mode operation, the amplifier must see a 2 Ohm load or higher for the stereo satellites and no lower than 4 Ohms for the subwoofer(s). Any lower than the above mentioned impedance will cause the amplifier to overheat and possibly cause permanent damage to the amplifier. SPEAKER CONNECTIONS (TRI-MODE) The ELA265, ELA2100 and ELA2150 are capable of running in a Mono / Stereo mode. This feature gives the amplifier the ability to run stereo satellites (midbass & tweeter) simultaneously with a mono subwoofer. These connections are more complicated because they require the use of passive crossover networks (Not provided) to divide the frequencies to the speakers. We have included a sample diagram for 4 Ohm connections. If you wish to use multiple speakers to achieve a lower impedance and higher power, it is strongly recommended that you seek professional advice from your BAZOOKA retailer before attempting to make these connections. Please Note: In the Tri-mode configuration, the amplifier’s built-in crossover must be set to the ”FLAT” position so the speakers receive full range output. NON-POLAR CAPACITOR INDUCTOR (COIL) L E G E N D 100 F - + 100 F + - - 4 mH Left Mid / Tweeter 4 Ohm (2 Ohm Minimum) Mono Woofer 8 Ohm (4 Ohm Minimum) Right Mid / Tweeter 4 Ohm (2 Ohm Minimum) ENGLISH REMOTE BASS CONTROL MODULE (OPTIONAL) Before connecting the remote, it will be necessary to find a mounting location that will be easy to access for adjustment. Once you select your mounting location, you will need to run the control wire from the remote to the amplifier. To avoid possibility of induced noise from the car's electrical system (i.e. popping noises or engine noise), run the cable from the remote to the amplifier away from the car's electrical wiring. ENGLISH ELA AMPLIFIERS GAIN SUBSONIC VOLUME PHASE BASS BOOST FILTER REMOTE X-OVER LINE IN LINE OUT MIN MAX 50Hz 250Hz OFF ON 0 180 6dB LPF FLAT 0dB 12dB LEFT RIGHT HIGH INPUT GND 14 MIN MAX ADJUSTING THE X-OVER AND BASS ENGLISH . (Please note: If you intend to use the ELA265, ELA2100 and ELA2150 in the Tri-mode configuration, it is necessary to set the crossover control to the “FLAT” setting in order to receive full range output) The “ELA” amplifiers are equipped with a built-in crossover network allowing you to select the crossover type (i.e. Low-Pass or Hi-Pass) and the desired crossover point. For example if you wish to drive a pair of subwoofers, you can select the “Low Pass” setting on the amplifier to filter out high frequencies. This will send only low frequencies to your subwoofers (see example settings below). You can add 6 or 12dB bass boost Select the crossover type on the amplifiers side panel. (Low-pass is selected in this example for subwoofers) by switching the Bass Boost control. Select the crossover point for your speakers. X-OVER X-OVER 250Hz 50Hz LPF FLATHPF BASS BOOST 6dB 0dB 12dB LEVEL FINE TUNE THE SYSTE...
Эта инструкция также подходит к моделям:Акустика - ELA1300 (6.8 mb)
Акустика - ELA1500 (6.8 mb)
Акустика - ELA1800 (6.8 mb)
Акустика - ELA2100 (6.8 mb)