Войти:
Оценок - 4, средний балл: 4 ( )

Инструкция по эксплуатации Jensen, модель JiSS-250i

Производитель: Jensen
Размер: 430.83 kb
Название файла: e32d2257-e890-42a9-a30c-f0e7732b9dac.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


- Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. PROTECT YOUR FURNITURE!! This system is equipped with non-skid rubber ‘feet’ to prevent the product from moving when you operate the controls. These ‘feet’ are made from non-migrating rubber material specially formulated to avoid leaving any marks or stains on your furniture. However certain types of oil based furniture polishes, wood preservatives, or cleaning sprays may cause the rubber ‘feet’ to soften, and leave marks or a rubber residue on the furniture. To prevent any damage to your furniture we strongly recommend that you purchase small self- adhesive felt pads, available at hardware stores and home improvement centers everywhere, and apply these pads to the bottom of the rubber ‘feet’ before you place the product on fine wooden furniture. 2 LOCATION OF CONTROLS LOCATION OF CONTROLS 1 2 3 4 5 6 1. LEFT SPEAKER 2. Docking Tray 3. Docking Connector 4. RIGHT SPEAKER 5. STANDBY BUTTON VOLUME +/- BUTTON 7. AUX IN JACK 8. DC IN JACK 9. FOLDABLE STAND 10. BATTERY DOOR 7 89 109 POWER SOURCE This Portable Speaker System is designed to operate on 4 x 1.5V ‘AAA’ (UM-4) batteries (Not included) or with the included AC Adaptor. GETTING STARTED A. DC OPERATION For better performance and longer operating time, we recommend using alkaline-type batteries. 1. Remove the battery door on bottom of the cabinet. 2. Observe the polarity markings inside the compartment and install 4 x 1.5V ‘AAA’ (UM-4) batteries correctly. 3. Replace the battery door. . IMPORTANT: Be sure that the battery is installed correctly. Wrong polarity may damage the unit. BATTERY CARE I. Do not mix old and new batteries. II. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries. III. If the unit is not to be used for an extended period of time, remove the battery. Any old or leaking battery can cause damage to the unit and may void the warranty. IV. Do not dispose batteries in fire. Batteries may leak or explode. 3 B. AC POWER CONNECTION 1. Plug the AC adaptor into a household 120V AC ~ 60Hz power source. 2. Insert the other plug into the DC INPUT Jack on the back of JiSS-250i. Note: The batteries will be automatically disconnected once the AC adaptor is plugged into the DC Jack and the System will operate on AC power. iPod ADAPTORS Below are the iPod Adaptors included in the package. iPod classic iPod touch iPod Nano 2nd iPod nano 3rd Gen. gen. iPod Nano 4th iPhone Gen. Note: No iPod adaptor is needed if you are using an iPod (5th generation) or iPod (4th generation). 4 DOCKING YOUR IPod DOCKING YOUR IPod 1. Fold out the STANDS located on the bottom of JiSS-250i. 2. Select a suitable adaptor attachment for your iPod/iPhone and insert it into the docking tray. Your iPod/iPhone can now be inserted onto the dock connector by aligning the connector on the bottom of the iPod onto the connector in the docking bay as shown below. For iPod/iPhone Landscape Viewing (iPod nano (4th gen), iPod touch, iPhone 2G, and iPhone 3G) proceed as below: 3. Choose the Correct adaptor to hold the iPod/iPhone and embed it at the iPod docking tray. 4. Extend the Speaker by pulling out the Left and Right Speaker 5. Insert the iPod firmly on the docking, now the iPod can be rotated freely into the Landscape position to the Left as shown. Note: - Please be careful when seating the iPod/iPhone into the docking to avoid damaging the 30-pin connector on the iPod or in the docking system. -The iPod/iPhone will start charging immediately when it is docked. -The iPod/iPhone will only be charged when the device is powered by an AC adaptor. 6. Turn the JiSS-250i on by pressing the STANDBY Button on the front panel. 7. Follow the iPod/iPhone operation instructions to operate your iPod/iPhone. 8. Adjust the sound level by pressing the VOL +/-buttons on the JiSS-250i. Note: The volume level cannot be adjusted using the volume control on your iPod after docking. 9. To remove the iPod/iPhone from the unit, press and hold the PLAY/PAUSE Button for few 5 seconds to switch off the device and then gently remove it from the docking connector. 10. To turn JiSS-250i off, press the STANDBY Button again. Note: i. The System will automatically enter sleep mode 5 minutes after playback stops and switch to standby mode automatically after 30 minutes of no activity. In Sleep mode the LED will flash and in standby mode, the LED will go off. ii. The AUX In function is in higher priority than the iPod function. Make sure the AUX IN Jack is unplugged when you are going to enjoy the iPod music, otherwise the music of the iPod won’t be heard. iii. Your iPod/iPhone will only be charged whe...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории