Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
. . . . . . . . . . . . navigates in iPod menu ALBUM/PRESET -/+ 1 / 2 – selects a preset radio station – selects albums in USB mode – selects time zone in clock mode VOLUME 3 / 4 – adjusts the sound level OK for iPod . . . . . . . . . . . . . .confirms menu selection. 7 Dock connector – connects iPod player 8 USB jack – connects an external USB mass storage device 9 REPEAT ALARM / BRIGHTNESS CONTROL – switches off the alarm for a 9 minute period – changes the brightness of the display illumination 0 TUNING .1 / 2™ – adjusts clock/alarm time – tunes to radio stations – selects previous/next tracks in the iPod/USB mode – fast searches forward/backward in the iPod/USB mode MODE – selects different play modes: e.g. REPEAT or SHUFFLE (random order). 2; – starts/pauses playback in the iPod/USB mode 9 – stops playback in the iPod/USB mode ! 1 ALM / 2 ALM – activates/confirm alarm 1/alarm 2 time setting – displays alarm 1/alarm 2 time – switches off alarm 1/alarm 2 time @ DISPLAY – shows clock/alarm times and status of the set # AUX IN jack (3.5 mm) – connects to external audio source $ POWER jack – socket for AC/DC 9V adaptor % Pigtail – improves FM reception POWER SUPPLY Mains adaptor 1 Connect the mains adaptor to the set's DC 9V socket and to the power socket. Helpful hints: To avoid damage to the set, use only the adaptor supplied! The power rating is located on the bottom of the set. SELF-POWERED BACK-UP The self-powered back-up conveniently allows your alarm and clock time settings to be stored for up to 10 minutes when there is a power interruption e.g. AC power failure. The complete clock radio and backlight illumination will be switched off. If power supply returns after 10 minutes and the display shows: • clock time blinking - indicates you need to re-adjust the clock time. BASIC OPERATION. Switching on the system •Press POWER. ™ The system will switch to the last selected source. Switching the system to standby mode • In any source mode, press POWER. Illumination brightness Press REPEAT ALARM / BRIGHTNESS CONTROL once or more. • The brightness of the display can be adjusted: Bright . Low . Off . Bright . SETTING THE CLOCK 1 In standby mode, press and hold PROG/SET TIME until clock digits flashes. 2 Hold down or press .1 / 2™ repeatedly to set and adjust the hours. 3 Press PROG/SET TIME to confirm. ™ The clock digits for the minutes flash. 4 Hold down or press .1 / 2™ repeatedly to set and adjust the minutes. 5 Press PROG/SET TIME to confirm. 6 In clock mode, press ALBUM/PRESET -/+ 1 /2 to set your time zone. 7 To zoom in/out the clock display, press MODE in clock mode. TUNER 1 Press SOURCE repeatedly to switch on the radio (FM only). ™ Display shows the radio frequency of the last selected waveband. Your preset station is also shown if you are listening to a preset. (See 2) 2 Adjust the sound using VOLUME 3 /4. 3 To select preset stations, press ALBUM/PRESET -/+ 1 /2 once or repeatedly. TUNING TO RADIO STATIONS 1 Press and hold .1 / 2™ until the frequency in the display starts changing. ™ After the system tunes to a station of sufficient reception, display shows its frequency. •To tune to a weak station, press .1 / 2™ briefly and repeatedly until an optimal reception is found. To improve reception (FM): Extend and position the pigtail fully to obtain optimum reception. STORING AND USING PRESET STATIONS You can store up to 20 FM radio stations in the memory. 1 Tune to your desired station (see TUNING TO RADIO STATIONS). 2 Press PROG to activate the programming, and then press ALBUM/PRESET -/+ 1 / 2 to select a desired preset number. 3 Press PROG again to confirm. 4 Press ALBUM/PRESET -/+ 1 / 2 to listen to a preset station. AUTOSTORE: Automatic programming 1 Press and hold PROG for more than two seconds. ™Available radio stations will be automatically stored. USING THE ALARM GENERAL Two different alarm times can be set. This can be useful when you need to be woken up at a different time e.g. during the week and at the weekend, and you can set different wake-up modes: •Tuner mode. • iPod/USB mode. • Nature sound mode. •Buzzer mode. The gentle wake buzzer alarm increases its beep tone frequency within seconds. SETTING THE ALARM TIME AND MODE (See 3) 1 In any mode, press and hold 1 ALM or 2 ALM for two seconds. ™ AL1 / AL2 icon and the hour digits flash. 2 Hold down or press .1 / 2™ repeatedly to set and adjust the hours. 3 Press 1 ALM or 2 ALM to confirm. ™ AL1 / AL2 icon and the minutes digits flash. 4 Hold down or press .1 / 2™ repeatedly to set and adjust the mintues. 5 Press 1 ALM or 2 ALM to confirm. ™ The icon for the current alarm mode flashes. 6 Press .1 2™ / SOURCE repeatedly to select your desired alarm mode. • For Nature sound mode, press ALBUM/PRESET -/+ 1 / 2 to select your desired nature sound track. ™ At the set alarm time, the selected sound source or buzzer will switch on automatically. Helpful hints: – If you have selected TUNER alarm mode, make sure you have properly tuned to a station b...