Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Use a balanced cable when the signal cable length exceeds 15 feet, this will reduce excessive signal loss. Be sure to connect only line level input devices such as mixers and tape machines to this jack. 9. output volume – This knob is used to regulate the output signal being sent to another XSP-15P or other powered speaker. 10. Balanced XLR Line Input – This connection is designed to accept a balanced line input signal from a mixer or other line level device with a balanced output jack. Use a balanced cable when the signal cable length exceeds 15 feet, this will reduce excessive signal loss. 11. Treble control – This knob is used to regulate the amount treble applied to the output signal. The maximum amount of treble gain is +12dB and the maximum amount of treble ©American Audio® - - XSP Series - Instruction Manual Page 13 decrease is -12dB. Turning the knob in a counter-clockwise direction will decrease the amount of treble applied to a channel signal, turning the knob in a clockwise direction will increase the amount of treble applied to a channel signal. 12. 1/4” Line Output Jack – This jack is used to send the incoming line level signal from either of the Line Level Inputs Jacks to another XSP-15P or other powered speaker. 13. XLR LINE output – Using a XLR cable, use this port to daisy chain from your XSP-15P to another XSP-15P or other powered speaker. 14. Bass Control – This knob is used to regulate the amount bass applied to the output signal. The maximum amount of bass gain is +12dB and the maximum amount of bass decrease is -12dB. Turning the knob in a counter-clockwise direction will decrease the amount of bass applied to a channel signal, turning the knob in a clockwise direction will increase the amount of bass applied to a channel signal. 15. Power indicator led - LED lights up to indicate the speaker is on. 16. Clip Led - If this LED is lit it means your signal is clipping. To stop the signal from clipping lower the volume to the point where the LED is blinking along with the bass beat. 17. MASTER/THROUGH SWITCH - When the switch is in the Through position only the line level inputs will transmit a signal. The Mic Inputs will be disabled when the switch is in the Through position. When the switch is in Master position, the speakers output is effected by the line level control, mic volume control, and master volume control. When switching between Master & Through, make sure you either turn down the volume levels or switch off the speakers. 18. AC VOLTAGE SELECTOR - This switch is used to change the operating voltage. Operating voltage can be toggled between 115v or 230v/50~60Hz. Be sure the selector is set to the proper voltage for your area before attempting to operate the unit. Always be sure main power is shut off before change the position of the Voltage Selector Switch. 19. Main Power Inlet – This connector is used to supply main power to the unit via the included detachable power cord. The power connection uses an I.E.C. type connector, use only a power cord that matches this type of connection. Be sure to only connect this unit to a power outlet that matches the printed power label on the unit. Never use a power when the ground prong has been removed or broken off. The ground prong is used to reduce the risk of electrical shock in case of an electrical short. This cord is designed to fit in one direction only. Do not attempt to force a cord if it does not fit, be sure the cord is being inserted properly. 20. Fuse Holder – This housing stores the 5 amp GMA protective fuse. Always replace with the exact same type fuse, unless otherwise instructed, by an authorized American Audio® service technician. Replacing with any other type of fuse than that of the recommended fuse will void your unit warranty. 21. Main Power Switch – This is the main power ON/OFF button. A green LED directly above the power switch will glow indicating power is ON. Before main power is applied, be sure you have made all connections to the speaker. Remember to avoid damaging pops to the speakers, the mixer is turned on first and turned off last. Always turn down the INPUT VOLUME (3) before switching off the speaker. Never turn off the speaker when there is a running signal! XSP Series Controls and Features ©American Audio® - - XSP Series - Instruction Manual Page 14 XSP Series Typical Speaker Set-Up Typical XSP Series Output Set-Up AUX4AUX/INMADEINCHINAMODELNO.:Q-3433MKIIPOWERSOURCE: 115/230V~50/60Hz20WMINMAXTRIMOUTPUT XLR-XLR Balanced Cables Connections are the same for 12P & 15P Speakers XSP 10P XSP 10P ©American Audio® - - XSP Series - Instruction Manual Page 15 XSP Series Looping Speakers XSP Speaker Looping From Mixer MASTERTHROUGH MASTERTHROUGH To Next XSP Speaker (If Applicable) ©American Audio® - - XSP Series - Instruction Manual Page 16 XSP Series Rigging and Mounting Options Speaker Rigging Hardware – The XSP Series speakers m...