Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Do not over-tighten the knob onto the valve. Do not use tools to tighten connection. NOTE: If you are unable to make the connection, repeat steps 4 and 5. 6. Check that the hose does not contain kinks, does not contact sharp edges, and does not contact surfaces that may become hot during use. 7. Leak check all fittings before lighting your grill. See section on "Leak Testing" in this manual. LEAK TESTING: To prevent fire or explosion hazard: • DO NOT smoke or permit ignition sources in the area while conducting a leak test. • Perform test OUTDOORS only in a well ventilated area. • Never perform a leak test with a match or open flame. • Never perform a leak test while the grill is in use. WHEN TO PERFORM A LEAK TEST: • After assembling your grill and before lighting for the first time, even if purchased fully assembled. • Every time the LP gas cylinder is refilled or if any of the gas components are replaced. • Any time your grill has been moved. • At least once per year or if your grill has not been used for more than 60 days. WARNING DANGER DANGER CHECKING FOR LEAKS: 1. Create a mixture of 50% water and 50% liquid dishwashing soap. 2. Open the lid. 3. Insure all burner knobs are set to the OFF position. 4. Turn on the fuel supply at the LP cylinder valve. Turn the cylinder valve knob one turn counterclockwise. 5. Apply the soap water mixture to the following: A B C D E F G H I J Supply tank (cylinder) weld Connection nut to tank valve. Back side of connection nut to brass nipple. Brass nipple connection into regulator. Regulator connections to gas supply hoses. Gas supply hose connection to burner valve assembly. Burner valve stem caps. Burner orifice fittings. The full length of gas supply hose Tank valve to cylinder A B C D E F G HI J Watch For Bubbles 6. Check each place listed (A - J) for growing bubbles which indicates a leak. 7. Turn OFF gas supply at cylinder valve. 8. Turn on control knobs to release gas pressure in hose. 9. Turn control knobs to “off” position. 10. Tighten any leaking connections. 11. Repeat soapy water test until no leaks are detected. DO NOT use the grill if leaks cannot be stopped. Contact a qualified gas appliance repair service. 12. Turn OFF gas supply at cylinder valve until you are ready to use your grill. 13. Wash off soapy residue with cold water and towel dry. 14. Wait 5 minutes to allow all gas to evacuate the area before lighting grill. NOTE: The leak test must be performed in an area that has adequate lighting in order to see if bubbles are developing. DO NOT use a flashlight to check for bubbles. WARNING PRE-START CHECK LIST: Property damage, bodily harm, severe burns, and death could result from failure to follow these safety steps. These steps should be performed after the grill has been assembled, stored, moved, cleaned, or repaired. DO NOT operate this grill until you have read and understand ALL of the warnings and instructions in this manual. • Insure that the grill is properly assembled. • Check burner venturi tubes for blockage from insect nests. See section on "Cleaning and Maintenance". • Check that all burner venturi are seated properly over the valve outlets as shown in assembly instructions. The orifice must be inside the burner venturi for proper air/fuel mixing. • Inspect the gas supply hose for burns, chaffing, kinks, and proper routing before each use. Hoses should be at least 3 inches from hot surfaces. • Leak check all gas connections and hoses. See section on "Leak Testing". • Ensure that all electrical supply cords are properly grounded and are kept away from water and hot surfaces. • Position your grill on level ground in a well ventilated location, a safe distance from combustible materials and buildings. • Properly place an empty grease collection cup under the grease drain hole in the bottom of the grill to catch grease during use. • Your grill is covered with a plastic film to protect the stainless steel finish during shipment and assembly. This plastic film must be removed before operating your grill. Read, understand and follow all warnings and instructions contained in this manual. DO NOT skip any of the warnings and instructions contained in the preceding sections of this manual. LIGHTING INSTRUCTIONS: Follow the instructions exactly. 1. OPEN THE GRILL LID before attempting to light the burner so that fumes do not accumulate inside the grill. An explosion could occur if grill lid is down. 2. Check that all burner control knobs and the cylinder valve are turned to the OFF position. 3. Turn on the fuel supply by rotating the cylinder valve knob counterclockwise to full open. 4. DO NOT stand with head, body, or arms over the grill when lighting. WARNING WARNING WARNING LIGHTING THE BURNER: 1. Open lid before lighting. 2. Turn on either side of the burner by pressing in and rotating the control knob to the HIGH position. 3. Press and hold the igniter button until the burner ignites. 4. If burner does not ignite immediately, turn the burner c...