Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Read and follow all instructions and warnings on the supply hose safety tags. Read and follow all warnings in this manual concerning the safe use of LP gas cylinders and the hose and regulator before connecting cylinder to grill. Read and follow all warnings on the LP cylinder. CONNECTING HOSE AND REGULATOR 1. Check that the cylinder valve is closed by turning the knob clockwise. 2. Check that the grill’s burner control knobs are in the "OFF" positions. 3. Remove the protective plastic cap from the cylinder valve and the connection device. 4. Hold regulator and insert the nipple of connection device into the LP cylinder valve outlet. Ensure that the device is centered properly. 5. Turn the large coupling nut clockwise by hand and tighten to a full stop. Take care not to cross thread the coupling nut onto the cylinder valve. Do not over-tighten the knob onto the valve. Do not use tools to tighten connection. NOTE: If you are unable to make the connection, repeat Steps 4 and 5. 6. Check that the hose does not contain kinks, does not contact sharp edges, and does not contact surfaces that may become hot during use. 7. Leak check all fittings before lighting your grill. See section on "Leak Testing" in this manual. LEAK TESTING: To prevent fire or explosion hazard: • DO NOT smoke or permit ignition sources in the area while conducting a leak test. • Perform test OUTDOORS only in a well ventilated area. • Never perform a leak test with a match or open flame. • Never perform a leak test while the grill is in use or while grill is still hot. WHEN TO PERFORM A LEAK TEST: • After assembling your grill and before lighting for the first time, even if purchased fully assembled. • Every time the LP gas cylinder is refilled or if any of the gas components are replaced. • Any time your grill has been moved. • At least once per year or if your grill has not been used for more than 60 days. CHECKING FOR LEAKS: 1. Create a mixture of 50% water and 50% liquid dishwashing soap. 2. Open the lid. 3. Ensure all control knobs are set to the "OFF" position. 4. Turn on the fuel supply at the cylinder valve. Turn the cylinder valve knob one turn counter-clockwise. 5. Apply the soap water mixture to the following: Supply tank (cylinder) weld. Connection nut to tank valve. Back side of connection nut to brass nipple. Brass nipple connection into regulator. Regulator connections to gas supply hoses. Gas supply hose connection to side burner valve assembly. Side burner valve stem cap. Side burner connection to hose. Hose connection to gas manifold. The full length of gas supply hose. K Tank valve to cylinder. J I H G F E D C B A 8 WARNING Watch For Bubbles DANGER IMPORTANT SAFEGUARD • DO NOT REMOVE THIS TAG • TURN GAS ON AND OFF USINGVALVE ON L.P. GAS TANK. USE THIS RED CONTROL VALVE FOR FLAME ADJUSTMENT ONLY. A B C D E F G H I J K 6. Check each place listed (A–K) for growing bubbles which indicates a leak. 7. Turn off gas supply at cylinder valve. 8. Turn on control knobs to release gas pressure in hose. 9. Turn control knobs to "OFF" position. 10. Tighten any leaking connections. 11. Repeat soapy water test until no leaks are detected. 12. Turn off gas supply at cylinder valve until you are ready to use your grill. 13. Wash off soapy residue with cold water and towel dry. 14. Wait 5 minutes to allow all gas to evacuate the area before lighting grill. CAUTION! DO NOT use the grill if leaks cannot be stopped. Contact a qualified gas appliance repair service. NOTE: The leak test must be performed in an area that has adequate lighting in order to see if bubbles are developing. DO NOT use a flashlight to check for bubbles. WARNING PRE-START CHECK LIST: Property damage, bodily harm, severe burns, and death could result from failure to follow these safety steps. These steps should be performed after the grill has been assembled and prior to each use. DO NOT operate this grill until you have read and understand ALL of the warnings and instructions in this manual. PRE-START CHECK LIST: • Ensure that the grill is properly assembled. • Inspect the gas supply hose for burns, chaffing, kinks, and proper routing before each use. If it is evident there is excessive abrasion or wear, or the hose is cut, it must be replaced prior the grill being used. Replace with hose and regulator, Model No. 155-2400-0, which can be obtained by contacting customer service at 800-527-0717. • Leak check all gas connections and hose. See section on "Leak Testing". • Ensure that all electrical supply cords are properly grounded. Keep any electrical supply cord and the fuel supply hose away from any heated surfaces. Hose should be at least 3 inches from hot surfaces. • Position your grill on level ground in a well ventilated location, a safe distance from combustible materials, buildings and overhangs. • Properly place the empty grease tray under the grease drain hole in the bottom of the grill to catch grease during use. • DO NOT obstruct the flow of combustion and venti...