Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
5. Follow all instructions in the order that they are laid out in this manual. 6. Two people are required to lift the grill head onto the assembled cart. If you have any questions about assembly or grill operation, or if there are damaged or missing parts please call our Customer Care Department at 1-866-820-8686 between 9 AM and 5 PM (Eastern Standard Time). TOOLS REQUIRED FOR ASSEMBLY (tools not included) 3/8 (10mm) Flat and Philips Pliers Hammer Wrench, screwdrivers ratchet or driver BUILT-IN UNIT OPENING DIMENSIONS BUILT-IN UNIT OPENING DIMENSIONS OUTDOOR GFI ELECTRICAL OUTLET BUILT-IN SIDEBURNER MINIMUM 10 SQ IN OF VENTILATION REQUIRED ON EACH END OF CABINET W DH 1.”(44mm) 1.”(44mm) D W GAS INLET OPENING NON-COMBUSTIBLE MATERIAL RECOMMENDED - LOCATE ON RIGHT SIDE OF GRILL FOR ROTISSERIE USE. 34” (864mm) RECOMMENDED GAS INLET OPENING H5” (127mm) WARNING! CABINET FRAME, CABINET AND COUNTER TOP MUST BE MADE FROM NON-COMBUSTIBLE MATERIAL. MODEL OPENING DIMENSIONS NOTES W D H BIPRO600 37 3/4” 959mm 20 5/8” 524mm 8 7/8” 225mm SIDE BURNER 12 3/4” 324mm 16 1/2” 419mm 4 1/2” 114mm OPENING OF AT LEAST 5 SQ IN MUST BE PROVIDED FOR COMBUSTION AIR FOR SIDE BURNER. D 2” (51mm) 34” (864mm)RECOMMENDED W D W H H GAS INLET OPENING 5”(127mm) 2” (51mm) 34” (864mm)RECOMMENDED W D W H H GAS INLET OPENING 5”(127mm) BUILT-IN ACCESSORY OPENING DIMENSIONS BIZC450 / BIZC600 BUILT-IN ZERO CLEARANCE SHELLS FOR ENCLOSURES BUILT WITH COMBUSTIBLE MATERIALS Note: Accessory frames overlap opening by 1 .” on all 4 sides. OPENING DIMENSIONS PART # DESCRIPTION PICTURE W H D N370-0069 FLAT VERTICAL PAINTED DOOR 13 .” (337mm) 18 .” (464mm) N370-0071 FLAT VERTICAL STAINLESS DOOR 13 .” (337mm) 18 .” (464mm) N370-0070 FLAT HORIZONTAL PAINTED DOOR 18 .” (464mm) 13 .” (337mm) N370-0072 FLAT HORIZONTAL STAINLESS DOOR 18 .” (464mm) 13 .” (337mm) N370-0356SS CURVED STAINLESS STEEL DOOR 22 .” (572mm) 19 .” (502mm) N370-0357SS 308 SIZE 27” (686mm) 19 .” (502mm CURVED STAINLESS STEEL DOOR 450 SIZE N370-0358SS CURVED STAINLESS STEEL DOUBLE DOOR - 600/750 SIZE 35 .” (895mm) 19” (483mm) OPENING DIMENSIONS PART # DESCRIPTION PICTURE W H D N370-0361 PF STYLE STAINLESS STEEL DOOR 17” (432mm) 23 .” (591mm) N370-0359 PF STYLE STAINLESS STEEL SINGLE DRAWER 17 .” (438mm) 6 .” (171mm) 23” (584mm) N370-0360 PF STYLE STAINLESS STEEL TRIPLE DRAWER 17 .” (438mm) 22 .” (578mm) 23” (584mm) N370-0502 DOUBLE DOOR SMALL 28 .” (718mm) 20 .” (514mm) N370-0503 DOUBLE DOOR LARGE 37 .” (959mm) 20 .” (514mm) * FRAMES PROTRUDE FROM FACE OF CABINET BY .” N370-0504 SIDE BURNER NATURAL 12 .” (324mm) 4 .” (114mm) 16 .” (419mm) N370-0505 SIDE BURNER PROPANE 12 .” (324mm) minimum 16 .” (419mm) BIZC450 ZERO CLEARANCE SHELL - 450 SIZE 35 .” (911mm) 11 .” (283mm) 22 15/16” (584mm) BIZC600 ZERO CLEARANCE SHELL - 600 SIZE 44 .” (1121mm) 11 .” (283mm) 22 15/16” (584mm) BI ACCESSORY DRAWER INSTRUCTIONS BI ACCESSORY DRAWER INSTRUCTIONS 1. Unpack the drawer frame assembly. 2. Remove the drawers from the enclosure by fully extending them and then lifting up to remove them from the slides. 3. Shim the opening to ensure that the enclosure fits snuggly into the opening. Ensure that the side shims are located at the same height as the enclosure mounting holes. The bottom of the opening may need to be shimmed as well to ensure that the front of the enclosure is plumb. 4. Once the enclosure is level and square, fasten into place. (Fasteners not included). 5. Re-install the drawers by tipping the back of the drawer down into the slide. Once the wheels are inserted into the slide, lower the front of the drawer until it is level, then push in. Note: if the enclosure is installed with shims that are too thick, the wheel will not engage into the slide. The shim thickness will need to be reduced. 6. Remove the protective coating from all remaining surfaces. BI ACCESSORY DOOR INSTRUCTIONS 1. Unpack the door and frame. a. For the curved stainless steel doors, remove the door(s) from the frame by lifting the door while holding on to the pivot rod. This will allow the pivot rod to come out of the hole on the bottom of the frame. Once the pivot is removed from the bottom hole, the entire door can be dropped and removed from the frame. b. For the PF style stainless steel door, the door needs to be removed by loosening the center philips screw on the hinge furthest away from the door. This will allow the hinge to separate. c. For double door kits N370-0502/N370-0503, refer to the instuctions included with the door kit. 2. Center the frame in the opening. Mark the location of the pivot holes, top and bottom. Remember on the PT600 double doors, there will be a pivot rod on both ends. The PF style doors do not have pivot rods. Once all pivot holes are marked, remove the frame and using a 3/8” drill bit, drill out the clearance holes for the pivot rod. These clearance holes should be at least 1/2” deep. After the holes are co...