Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Go ahead and tighten Wheel Leg bolts securely. (This will not be possible after the Wheel is assembled.) Fixed Legs Wheel Legs All Wood Bottom Shelf/ Leg Assembly Fixed Legs Wheel Legs 6 STEP 3-Wheel Assembly (ITEM 8) Washer (Axle) (ITEM 10) Axle Nut 7 with Item 10 installed (ITEM 9) Wheel · Remove Axle Nuts from Axle. Insert Axle through both sides of Wheel Legs. Place Axle Washers onto each end of Axle. · Position Wheel hub recess to the outside and slide a Wheel onto each end of Axle. · Attach Axle Nut onto each end of Axle. Tighten each side with wrench or pliers. Wheel hub recess this side Axle Washer Axle Nut STEP 4-Slide Vent Assembly (ITEM 12) Slide Vent (ITEM 13) Bolt, 6mm (ITEM 11 or 11A) Body Assembly (ITEM 16) Locknut, 6mm (ITEM 15) Sleeve Spacer, 6mm (ITEM 14) Washer, 6mm · Open the Hood on the Grill Body. · Align slotted holes in Slide Vent with holes in Grill Body Side. · Insert a 6 mm x 16 Bolt through the 6mm Steel Washer and Sleeve Spacer. Position this assembly with the Sleeve Spacer inside the Slide Vent slotted hole. Attach 6mm Steel Washer and Locknut to Bolt from inside of Grill Body to secure the Slide Vent. Repeat for each slotted hole on both Slide Vents. · Make sure the Vents slide back and forth freely over the Sleeve Spacers. If not, loosen the bolts slightly and reset the Spacers inside the Slide Vent slotted holes and retighten. Sleeve Spacer inside slotted hole of Slide vent 8 STEP 5-Hood Handle Assembly (ITEM 14) Washer (ITEM 17) Bolt, 6mm x 90 mm 6 mm (ITEM 16) Locknut (ITEM 19) Handle Spacer 6mm (ITEM 18 or 18A) Hood Handle · Open Hood and lay it on on its backside. · Insert 6 mm x 90 mm Bolt through recessed hole of Hood Handle, through Handle Spacer through a hole in Hood. (Note: Wide end of Handle Spacer goes against the Hood.) · Attach a 6mm Washer and Locknut to the Bolt from inside Hood. Do not over tighten; it may crack the Hood finish. · Repeat for other end of Handle. Assembled Handle STEP 6-Grill Body/Cart Assembly (Continues on next page) Assembly of Grill Body will require two people. (ITEM 17) Bolt, 6mm x 90 mm (ITEM 20) Body Spacer (ITEM 21) Wingnut, 6mm 9 (ITEM 11 or 11A) Body Assembly (ITEM 17A) Bolt, 6mm x 110 mm STEP 6-Continued Grill Body/Cart Assembly (See also page 11 for Wood Cart Assembly) · Carefully lay Grill Body Assembly on its back side with Front panel facing up and Hood open. Lay Cart Assembly on the back side with the Grill Body between Side Tables. (Note: Wheels on Cart assembly are to the left.) (FIG. A) · Align slotted holes on sides of Grill Body Assembly with holes in edges of legs (FIG. B). Insert Body Spacers between Leg and Grill Body. (You can pull the legs away from the body since all the bolts are loose.) Insert two 6mm x 90mm Body Bolts through Leg, Spacers and slotted holes in Grill Body. Attach a 6mm Wing Nut to the Bolts, but do not tighten. Repeat this assembly for remaining three Cart Legs. · With help from a second person, turn full Grill and Cart Assembly upright. The Grill Body should slide down to seat itself within the slotted holes. If not, loosen the Body bolts and push down at all four corners. · Tighten all Body Bolts and Wing Nuts. · Tighten all other Bolts at his time. View from inside Body/Cart Assembly View from back side of Leg/Body Assembly after standing up FIG. A FIG. B BoltBody Spacer Wingnut 10 FIG. A FIG. B View from inside Body/Leg Assembly Bolt Body Spacer Wingnut View from back side of Body/Leg Assembly after standing up STEP 6-Grill Body/Wood Cart Assembly View from inside Body/Leg Assembly Bolt Body Spacer Wingnut View from back side of Body/Leg Assembly after standing up STEP 6-Grill Body/Wood Cart Assembly 11 STEP 7- Install Drip Pan, Charcoal Grate & Cooking Grid (ITEM 23) Charcoal Grate(ITEM 22) Drip Pan (ITEM 24) Cooking Grid · Slide Drip Pan back into Grill Body. Make sure the Drip Pan is pushed all the way in. · Hang Charcoal Grate inside Grill Body by hooking the handles inside the two (2) elongated slots on each side of the Grill Body. · Lay the Cooking Grids on the front and rear Body shoulders above the Charcoal Holder. Install Grids on Front and Rear Shoulder of Body Slide Drip Pan under Body Hook Handles into slots 12 OPERATING AND MAINTAINING YOUR CHARCOAL GRILL BEFORE USING YOUR CHARCOAL GRILL USING CHARCOAL To reduce the risk of serious bodily injury or death: · Be careful when burning charcoal to avoid getting burned from flame, heat or hot coals. · Burning charcoal consumes oxygen and produces toxic gases, including carbon monoxide that can kill. · Be aware of the wind blown sparks. · Always have an ABC fire extinguisher, baking soda, a bucket of sand or a garden hose ready in case of an uncontrolled fire. Use a high quality hardwood charcoal to make sure you get a good fire. Charcoal briquettes made from maple, oak, birch or elm woods will burn clean with very little smoke and without unpleasant odors. SELECTING A LOCATION To reduce the risk of serious bodily injury or death: · Loca...
Эта инструкция также подходит к моделям:Грили - MONARO 7652K6 (1.11 mb)
Грили - MONARO 7652K1 (1.11 mb)