Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
6 The L.P. gas cylinder must have a shut-off valve terminating in a Type 1 L.P. gascylinder- valve outlet. A Type 1 compatible cylinder with a Type 1 cylinder valve has a positive seating connection that does not permit gas flow until a positive seal has been obtained. The cylinder must be arranged for vapor withdrawal. It must also include a collar to protect the cylinder valve. A safety-relief device having direct communication with the vapor space of cylinder must be provided. This will expel high-pressure gas if the cylinder is overfilled or overheated. All L.P. gas cylinders used with this appliance shall be constructed and marked in accordance with the specifications for L.P. gas cylinders of the U.S. Department of Transportation (DOT) or the National Standard of Canada, CAN/CSA-B339, Cylinders, Spheres and Tubes for Transportation of Dangerous Goods; and Commission, as applicable; and shall be provided with a listed overfilling-prevention device. Read labels on the L.P. gas-supply cylinder. DANGER: Do not insert any foreign objects into the valve outlet. You may damage the back check, A damaged back check can cause a leak, which could result in explosion, fire, severe personal injury or death. Allow only a qualified L.P. gas dealer to fill or repair an L.P. gas-supply cylinder. Inform the gas dealer if it is a new or used cylinder to be filled. Caution the gas dealer not to overfill the fuel cylinder. Have the gas dealer weigh the cylinder after filling to ensure that the cylinder is not overfilled. DANGER: a.) Do not store a spare L.P. gas cylinder under or near this appliance. b.) Never fill the gas cylinder beyond 80 percent full. c.) If the information in (a.) and (b.) Is not followed exactly, a fire causing serious injury or death may occur. TRANSPORTING A FULL CYLINDER WARNING: Handle a full cylinder with care. Gas is under high pressure. You should transport only one cylinder at a time. Transport the cylinder in an upright and secure manner with the control valve turned off and the POL dust cap in place. Do not transport a cylinder in the passenger compartment of a vehicle. Do not leave cylinder in direct sunlight or in a high-heat area such as a closed car trunk. High-heat areas could cause the relief valve to vent gas. Use a cylinder cap on the cylinder-valve outlet during transport and when the cylinder is not connected to the grill. Keep cylinder valve closed when not in use. After filling, have the gas dealer check for leaks and that the relief valve remains free to function. 7 Type1(cutawaytoseefitting) Take These Instructions to the L.P. Gas Dealer When using a cylinder exchange, be sure the exchanged cylinder is a Type 1 cylinder; a 510 POL cylinder will not fit a Type 1 regulator. FILLING AND PURGING TYPE 1 L.P. GAS CYLINDERS DANGER: Purging and filling of L.P. gas cylinders must be performed by personnel who have been thoroughly trained in accepted L.P. gas industry procedures. Failure to follow this instruction may result in explosion, fire, severe personal injury or death. IMPORTANT: Purge new cylinders before filling. This tank is easily filled with a standard CGA 510 POL filling connection. ExampleACGA-510POL Filling a Type 1 Cylinder Valve Example A: shows a CGA-510 POL fitting. Example B: shows using a Type 1 POL fitting. Example B The L.P. gas cylinder has a Type 1 cylinder valve with a back-check module in its outlet that will not permit gas to flow until an evacuation device is installed. To purge the L.P. gas cylinder, the back-check module must be opened with an evacuation device. PURGING AND EVACUATION DEVICES FOR L.P. GAS CYLINDER WITH TYPE 1 CYLINDER VALVES A. Hose-end valve with a bleed port: Purging can be accomplished using a hose-end valve containing a bleed port, which also allows for evacuation without the use of an adapter. B. Hose-end valve without a bleed port: When a hose-end valve does not have a bleed port, a separate device must be used for evacuation. C. Purging using a Type 1 connection: L.P. gas cylinder evacuation can be accomplished during each purging by using a Type 1 connection. The Type 1 valve outlet has 15/ 16” external ACME right-hand thread that will accept this connection. CAUTION: After purging or filling an L.P. gas cylinder, do not insert a POL plug into the valve outlet. Insertion of this plug will prevent the back-check from closing. Use ONLY the provided cap and strap attached to the outlet. Close the cylinder valve knob before returning the cylinder to the customer. For proper purging procedures in the USA, refer to: Safety Bulletin NPGA # 133, “Purging L.P. Gas Cylinders,” and Safety Bulletin NPGA #130, “Recommended Procedures for Filling Cylinders.” DANGER: Do not fill an L.P. gas cylinder beyond 80% full. If this information is not followed exactly, a fire causing serious injury or death may occur. 8 X-Frame Model Series Gas Grill Assembly Instructions Chapter 2 Getting Started 1. Please follow the steps in the order that they are pr...