Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Pull forward to remove. Spills should be washed off as soon as possible to prevent baked on soil. 12 GENERAL CLEANING BURNERS For proper lighting and performance keep the burners clean. It is necessary to clean the burners if they do not light even though the igniter clicks, if there has been a severe boil over, or when the flame does not burn blue. Be certain all burner knobs are in the off position before attempting to clean the burners. The burners have been designed for ease in cleaning. When the grate and burners are cool, remove the grate. The burner cap and the brass port ring can easlily be lifted off. Wash these parts in hot soapy water, rinse and dry thoroughly. The burner caps are porcelain enamel, follow the directions on the previous page that were given for the burner grates. A bristle brush can be used to clean out the toothed burner ports, if necessary. After cleaning, it is important to make sure the location pins on the bottom side of the port ring are properly aligned with the corresponding holes in the base. Incorrect alignment will produce a potentially dangerous flame and poor burner perfomance (see Fig.09). IGNITERS Wipe with a water dampened cotton swab. not to damage the igniter (see Fig.10) FIG.09 Brass Ring Locating Pins Electrode Main Burner Port Ring Locating Notch Burner Base Venturi Cap Locating Holes Be careful IGNITER (KEEP CLEAN) FIG.10 13 TROUBLESHOOTING PROBLEM WHAT TO DO Burner won’t light when the ignition is pushed. Remove the burner grate. With the control knob in the “OFF” position, listen to the electrode while engaging the ignition. You should hear a spark jump inside the electrode cap.When the spark jumps, it makes a ticking sound. If there is no spark........ Could be a dead battery. Or the air gap between an electrode tip and a contact metal is too far (gap should be 1/8”) or dirty. If there is a spark... is there gas supplied to the unit and is the line purged of air? See Fig. 03 and Fig. 04. Does the other burner of a dual burner operate? Check the orifice for blockage or venturi blockage. Burner flame is yellow or orange, in Check the burner for obstructions or dirt. See Fig. 09. conjunction with the odor of gas. Check for proper gas supply or wrong gas. Is the Side Burner in a dusty area? Move to less dusty area if possible. Low heat with knob in “HI” position. Is the fuel hose bent or kinked? See Fig. 03 and Fig. 04. Is there adequate gas supply available? If it is only one burner of the dual burner unit that appears low, does the burner need cleaning? See Fig. 09 and Fig. 10. If using LP gas, check for empty tank or low. 14 15 SINGLE SIDE BURNER PARTS LIST FOR BGB131 & BGB131-BI NOTE: Part list typical for BGB131 & BGB131-BI models. Illustration shows BGB131-BI model. ITEM DESCRIPTION PART NO. 1 BURNER COVER 33316 2 PULL HANDLE 18204-01 3 RUBBER BUMPER 18403 4 TOP GRATE BK 12020 5 D BURNER CAP 12272 6 PORT RING ASSEMBLY 12333 7 VENTURI 12332 8 BASE D BURNER 12321 9 PLATE SUPPORT BURNER 33314 PLATE SUPPORT BURNER (BGB131-BI) 33434 10 BURNER HANGER 33315 11 JET HOLDER LP 12200-17 JET HOLDER NAT 12200-08 12 DRIP PAN ST. STL (BGA131-BI MODEL) 32348-02 DRIP PAN ST. STL (BGB131 MODEL) 33306-02 13 DRIP PAN HANDLE DBI (BGA131-BI MODEL) 33035 DRIP PAN HANDLE 131/132 (BGB131 MODEL) 33307 14 1.5VDC BATTERY AA 16567 ITEM DESCRIPTION PART NO. 15 BEZEL 14006-PL 16 CONTROL KNOB 14351 17 IGNITION MODULE 16566 18 WIRE BLACK W/ TERMINALS 8” 16438-03 19 WIRE BLACK W/ TERMINALS 10” 16438-06 20 TUBING 5/16” (9” LENGTH) 18537 21 ELBOW 1/8NPT X 5/16 T.O.D. 18530 22 FERRULE 5/16 18301-02 23 NUT M22 JET HOLDER 12150 24 NUT 1/2-24UNF 18301-01 25 MANIFOLD (BGB131-BI MODEL) 18230-02 MANIFOLD (BGB131 MODEL) 18502 26 MANUAL GAS VALVE 13017-01 27 VALVE PANEL (BGA131-BI MODEL) 33351-PA VALVE PANEL (BGB131 MODEL) 33320-PA 28 VALVE PANEL SCREWS (BGB131-B1) 15002-41 29 ELECTRODE 12224 30 SPRING ELECTRODE 12230 31 CLIP ELECTRODE 12231 2 1 4 5 6 7 25 26 11 8 17 16 14 15 13 12 9 10 27 28 20 18 19 24 22 23 21 3 29 30 31 16 DOUBLE SIDE BURNER PARTS LIST FOR BGB132 & BGB132-BI NOTE: Part list typical for BGB132 & BGB132-BI models. Illustration shows BGB132-BI model. ITEM DESCRIPTION PART NO. 1 BURNER COVER 33299 2 PULL HANDLE 18204-01 3 RUBBER BUMPER 18403 4 TOP GRATE BK 12013-1 5 D BURNER CAP 12272 6 PORT RING ASSEMBLY 12333 7 VENTURI 12332 8 BASE D BURNER 12321 9 PLATE SUPPORT BURNER 33297 PLATE SUPPORT BURNER (BGB132-BI) 33435 10 BURNER HANGER (BGB132 MODEL) 33298 11 JET HOLDER LP 12200-17 JET HOLDER NAT 12200-08 12 DRIP PAN ST. STL (BGA132-BI MODEL) 32348-01 DRIP PAN ST. STL (BGB132 MODEL) 33306-01 13 DRIP PAN HANDLE (BGA132-BI MODEL) 33035 DRIP PAN HANDLE 131/132 (BGB132 MODEL) 33307 14 1.5VDC BATTERY AA 16567 15 BEZEL 14006-PL ITEM DESCRIPTION PART NO. 16 CONTROL KNOB 14351 17 IGNITION MODULE 16566 18 WIRE BLACK W/ TERMINALS 10” 16438-06 19 WIRE BLACK W/ TERMINALS 18” 16438-07 20 TUBING 5/16” (21” LENGTH) 18538 21 ELBOW 1/8NPT X 5/16 T.O.D. 18530 22 TUBING 5/16” (9” LENGTH) 18537 23 NUT M22...
Эта инструкция также подходит к моделям:Грили - BGB131-BI (372.49 kb)
Грили - BGB132-BI (372.49 kb)
Грили - BGB132 (372.49 kb)