Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
WARNING Use only parts supplied with this kit. Use of any parts other than those supplied with this kit will void the warranty and could cause unsafe conditions or improper operation of your appliance. WARNING Drain the tank and ensure that appliance has cooled to room temperature before performing this upgrade. DO NOT work on a hot appliance or an appliance containing hot cooking medium; serious personal injury may occur. TO THE PURCHASER Post in a prominent location the instructions to be followed in the event that an operator smells gas. Obtain this information from your local gas supplier. WARNING There is an open flame inside this appliance. The unit may get hot enough to set nearby materials on fire. Keep the area around the appliance free from combustibles. WARNING DO NOT use an open flame to check for gas leaks! WARNING Adequate means must be provided to limit the movement of this appliance without depending on the gas line connection. If any restraining devices are disconnected during this procedure, ensure that they are reconnected before putting the appliance into service. Failure to do so could result in a dangerous and unsafe condition. WARNING Installation of this upgrade kit should only be performed by a competent service technician. WARNING Do not attempt to move a cooking appliance when the unit is at operating temperature. Serious personal injury could result if skin comes in contact with the hot surfaces. WARNING DO NOT sit or stand on this appliance. Serious injury could result from falling or contact with hot shortening/oil. WARNING Improper installation, alteration, service or maintenance can cause property damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment. WARNING If gas flow to appliance is interrupted, or pilots extinguish, wait 5 minutes before attempting to relight the pilot to allow any residual gas in appliance to dissipate. NOTICE It is recommended that your appliance be inspected by a qualified technician on a yearly basis. L80-029 Rev 5 10/07 Theory of Operation: A natural gas burning appliance requires roughly 10 cubic feet of air to properly combust a single cubic foot of gas. Minute airborne particles entrained during this process pass through the combustion system and are incinerated. However, some particles may be trapped within the combustion system, building up over time, causing an eventual decrease in the operational efficiency of your appliance. The rate at which this build up may occur varies from kitchen to kitchen and is greatly influenced by the environment (breading, flour etc.) and kitchen processes (i.e. cleaning). Historically, frequent cleaning of burners and other combustion related components has been the only way to insure optimal efficiency of your fryer. The Pitco Self Cleaning Burner System (SCBS) will minimize the cost and inconvenient down time of frequent cleaning of combustion system components. Each morning when the appliance is turned on, a small amount of gas is momentarily diverted into a runner tube, which, after passing by the pilot, ignites and causes a short but effective light back at the main burner orifice. This brief flame bath cleans the inside of the burner face by incinerating any foreign matter that has accumulated from the previous day’s operation. The Pitco Self Cleaning Burner System is designed to help maintain proper operation and efficiency of your appliance’s combustion system by minimizing the build up of any foreign material inside the burner housings. Proper installation of this upgrade and periodic maintenance of the appliance are critical to safe, reliable and efficient operation. Tools required to perform this upgrade: 5/16” (8 mm) wrench 1 1/16” wrench Wire cutters 5/16” (8 mm) nut driver Cordless screwdriver w/ 5/16” bit Pipe joint compound or teflon 7/16“ (12 mm) wrench Phillips screwdriver tape 1/2“ (13 mm) wrench Small flat blade screwdriver 11/16” (18 mm) wrench (or socket) 3/16” (5 mm) hex key 7/8” (23 mm) wrench Before you begin: Verify that you have all the parts for the model that you are upgrading by checking the kit number and contents against the exploded view drawings in the back of these instructions. WARNING The power supply to the appliance MUST be disconnected before performing this procedure. WARNING Ensure that the gas supply to this appliance is turned OFF before performing this procedure. WARNING Drain the tank and ensure that appliance has cooled to room temperature before performing this upgrade. DO NOT work on a hot appliance or an appliance containing hot cooking medium; serious personal injury may occur. 1 L80-029 Rev 5 10/07 Follow this procedure for Installation of Self Cleaning burners and SCBS arm: a. Disconnect the control harness from the main gas valve and tuck it out the way to avoid damaging the harness during this procedure. b. If your appliance has a solid-state control (or auxiliary therm...