(6.8 m) Recommended standard fittings 3-1/4" x 10" (8.3 cm x 25.4 cm) to 6" (15.2 cm) = 4.5 ft. (1.4 m) 6" (15.2 cm) to 3-1/4" x 10" (8.3 cm x 25.4 cm) = 1 ft. (0.3 m) 3-1/4" x 10" (8.3 cm x 25.4 cm) to 6" (15.2 cm) 90° elbow = 5 ft. (1.5 m) 6" (15.2 cm) to 3-1/4" x 10" (8.3 cm x 25.4 cm) 90° elbow = 5 ft. (1.5 m) 90° elbow = 5 ft. (1.5 m) 45° elbow = 2.3 ft. (0.8 m) 6" wall cap = 0 ft. (0 m) WARNING Installation steps Excessive Weight Hazard Use two or more people to move and install downdraft

When making the electrical connection, cut a 1 1/4" hole in the wall. A hole cut through wood must be sanded until smooth. A hole through metal must have a grommet. WARNING -TOREDUCETHERISKOFFIREORELECTRIC SHOCK, do not use this fan with any solid-state speed control device. WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. Before

For best results, use no more than three 90° elbows. Make sure that there is a minimum of 24" of straight duct between elbows if more than one is used. Do not install two elbows together. If you must elbow right away, do it as far away from the hood's exhaust opening as possible. 45. Elbow 3.0 feet 90. Elbow 5.0 feet 90. Flat Elbow 12.0 feet Wall Cap0.0 feet FIGURE 2 9 Feet Straight Duct 9.0 feet 2 - 90. Elbows 10.0 feet Wall Cap 0.0 feet Total System 19.0 feet FIGURE 3 Version 03/08- Page 5 INS

FIGURES 1 and 2 show vertical and horizontal installations for this unit. FIGURE 3 shows recirculating installation. TheMagnumrequires6"roundductwork. Toensure that the blower performs to its highest possible capacity, ductwork should be as short and straight as possilbe. WARNING! BEFORE MAKING ANY CUTS OR HOLES FOR INSTALLATION, DETERMINE WHICH VENTING METHOD WILL BE USED AND CAREFULLY CALCULATE ALL MEASUREMENTS. CALCULATE THE DUCTRUN LENGTH The ductrun should not exceed 35 equivalent feet if d

In a ducted application, this rangehood can be vented through the wall or ceiling. To vent through a wall, a 90° elbow is used. When installed ductless, the rangehood vents out of grates on the sides of the chimney. Ductless installations require a Ductless Conversion Kit, available from your dealer. WARNING! BEFORE MAKING ANY CUTS OR HOLES FOR INSTALLATION, DETERMINE WHICH VENTING METHOD WILLBE USED AND CAREFULLY CALCULATE ALL MEASUREMENTS. FIGURE 1RANGEHOOD ASSEMBLY PLAN THE INSTALLATION The P

Label which cable is the 120-volt supply wire and which is the exterior blower cable. Now Start... Cover countertop or cooking surface with a thick, protective covering to prevent damaging them. 2-3/4" 5-15/16" (7.0 cm) (15.1 cm) wall A B 17-5/16" 11" (27.9 cm) 5/16" (7.9 mm) (40.0 cm) dia. dia. 4-holes hood size A B 36" (91.4 cm) 31-7/16" (79.9 cm) 15-23/32" (39.9 cm) 48" (121.9 cm) 43-7/16" (110.3 cm) 21-23/32" (55.2 cm) 1. Mark the locations of four 5/16" (7.9 mm) dia. holes and an 11" (27.9

For best performance, use no more than three 90° elbows. To calculate the length of system you need, add the equivalent feet (meters) for each vent piece used in the system. See the following example. 90° elbow 6 ft. (1.8 m) 3 ft. (0.93 m) 3-1/4" x 10" (8.3 cm x 25 cm) vent system 3-1/4" x 10” wall (8.3 cm x 25 cm) cap Maximum length = 26 ft. (8 m) 1 — 90° elbow = 5 ft. (1.5 m) 9 ft. (2.8 m) straight = 9 ft. (2.8 m) 1 — wall cap = 0 ft. (0 m) Length of 3-1/4" x 10" (8.3 cm x 25 cm) system = 14 f