|
Инструкция по эксплуатации Sony, модель STR-DN1000
К этому устройству также есть другие инструкции:
Фрагмент инструкции
ON, DEC. OFF DEC. OFF HDMI settings [] Control for HDMI [CTRL:HDMI] CTRL ON, CTRL OFF CTRL OFF Setting HDMI audio input [AUDIO OUT] AMP, TV+AMP AMP Subwoofer level for HDMIf) [SW LEVEL] SW AUTO, SW +10 dB, SW 0 dB SW AUTO System settings [] Naming inputs [NAME IN] For details, see “Naming the input (Name Input)” (page 48). Brightness of the display [DIMMER] 0% DOWN, 40% DOWN, 70% DOWN 0% DOWN S-AIR settings [] S-AIR IDg) [S-AIR ID] ID: A, ID: B, ID: C ID: A Pairingg) [PAIRING] START, CONDITION START S-AIR modeg) [S-AIR MODE] PARTY, SEPARATE PARTY RF Changeg) [RF CHANGE] RF AUTO, RF ON, RF OFF RF AUTO S-AIR Standbyg) [S-AIR STBY] STBY ON, STBY OFF STBY OFF a)■■■ represent a speaker channel (FL, FR, CNT, SL, SR, SB, SBL, SBR, SW). b)Depends on the speaker pattern setting, some parameters or settings may not be available. c) You can only select this parameter if “SP PATTERN” is not set to a setting with surround back speakers (page 66). d)You can only select this parameter if your speaker is set to “SMALL”. e)You can only select this parameter if you select Cinema Studio A/B/C as sound field. f) This parameter is only available when HDMI input signals are detected. g)This parameter is only available if the S-AIR transmitter (not supplied) is inserted to the EZW-T100 slot on the receiver. 80GB Changing the display You can check the sound field, etc., by changing the information on the display. Press DISPLAY repeatedly. Each time you press DISPLAY, the display will change cyclically as follows. All inputs except the FM and AM band Input name you selecteda) —► Original input name —— Sound field currently applied —— Volume level —— Stream information FM and AM band Program Service nameb) or preset station namea) —— Frequency —— Program Type indicationb) — Radio Text indicationb) — Current Time indication (in 24-hour system mode)b) —— Sound field currently applied —— Volume level a) Index name appears only when you have assigned one to the input or preset station (page 48, 54). Index name does not appear when only blank spaces have been entered or it is the same as the input name. b)During RDS reception only (Models of area code CEL, CEK only) (page 54). Note Character or marks may not be displayed for some languages. Tip You cannot switch the display while “GUI” is shown on the display. Press GUI MODE repeatedly to select “MENU OFF”. Performing Auto Calibration For details on the Auto Calibration, see “9: Calibrating the appropriate speaker settings automatically (Auto Calibration)” (page 39). See “Before you perform Auto Calibration” (page 39) before performing the Auto Calibration. To operate on the receiver 1 Press GUI MODE repeatedly to select “MENU OFF”. 2 Press AMP. Receiver operation is enabled. 3 Press MENU. 4 Press v/v repeatedly to select “” , then press ©. 5 Press v/v repeatedly to select “A.CAL START”, then press © to start the measurement. Measurement starts in 5 seconds. A count down is displayed. Note While the time is counting down, stand away from the measurement area to avoid measurement error. 6 Measurement starts. The measurement process will take approximately 30 seconds. Wait until the measurement process completes. To cancel Auto Calibration The measurement will be canceled when you do the following: - Press 1/1, input buttons or MUTING. - Press SPEAKERS on the receiver. - Change the volume level. - Connect the headphones. continued 81 SB Amplifier Operations Tips • Operations other than turning the receiver on or off are deactivated during Auto Calibration. • The measurements may not be performed correctly or Auto Calibration cannot be performed when special speakers, such as dipole speakers are used. To confirm/save Auto Calibration when GUI function is turned off 1 Confirm the measurement result. When the measurement ends, a beep sounds and the measurement result appears on the display. Measurement Display Explanation result When the COMPLETE Proceed to step measurement process completes properly 2. When the E - See “Message measurement process fails Calibration measurement” (page 43). Press v/v repeatedly to select the item, then press © Item Explanation RETRY Performs the Auto Calibration again. SAVE EXIT Saves the measurement results and exits the setting process. WARN CHECK Displays a warning concerning the measurement results. See “Message list after Auto Calibration measurement” (page 43). PHASE INFO. Displays the phase of each speaker (in phase/out of phase). See “When you select “PHASE INFO.”” (page 83). DIST. INFO. Displays the measurement result for speaker distance. LEVEL INFO. Displays the measurement result for speaker level. Item Explanation EXIT Exits the setting process without saving the measurement results. 3 Select “SAVE EXIT” in step 2. The measurement results are saved. 4 Press v/v repeatedly to select the Auto Calibration Type, then press ©....
Напишите ваш отзыв об устройстве
|
|
)
