Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
The tape will stop at the end of side '‘B”. 5 Press the ATC button. ATC (auto tape calibration) will begin, and will be completed in approximately one minute. (For detailed information, refer to "About the ATC function” on page 13.) [Recording is also possible without performing ATC.] 6 The sound source to be recorded should be played before the recording Is started in order to adjust the recording level. 7 Press the record button. (The recording indicator will illuminate and the playback indicator will flash continuously. The unit will be in the recording stand-by mode.) 8 Adjust the recording level. While watching the level on the Input level meter, adjust the "REC LEVEL” control so that the peak Indication is as high as possible, without exceeding the Indication noted in the chart below. Normal, Cr02 tape 0 Metal tape +2 9 Adjust the left/right recording balance. 1 0 Stop playback of the source. 1 1 Start recording, then start playing the source to be recorded from the beginning. The playback indicator will illuminate steadily, and the recording will begin. If only one side of the tape (reverse mode position: ) is to be recorded, press the playback button that corresponds to that side. To record on both sides of the tape (reverse mode position: CD ), press the “A” side playback button (►). ■ To temporarily stop recording Press the pause button. (The playback indicator will begin flashing.) ■ To stop recording Press the stop button. To resume recording, press the pause button again or press the playback button corresponding to the side of the tape being recorded upon. 1 About the ATC function ATC (auto tape calibration) is the function which identifies the quality of the tape (concerning bias, level, equalizer) automatically and sets the most desirable recording condition. It takes about 1 minute to complete the setting. ATC ATC button © (on both decks) [For RSTR777: deck 2 only] ATC will begin when the ATC button on the deck in which the cassette for recording is Inserted is pressed. Perform ATC while the other deck is in the stop (or rewind/fast-for-ward) mode. Because the ATC function records a test signal onto the tape, any previously recorded material will be erased, so be careful not to accidently erase material which you wish to save. Although ATC can also be performed for a tape which is partly wound, it is not possible at the end of the tape. Although the tape will be wound back to its original position after ATC has been completed, the position may be slightly different from the exact original position. Therefore, perform ATC 2 seconds or more after the end of the previous track. Be sure to set the bias adjustment control to 0. Equalizer setting in progress. n n n n u u.u u j o, 400 • Ik * 10k *~J B ¿1 iTlf ill f tiff lit tiilf lilt tfñ i rAimirftffif+a n M1111IIMMIIIIIIIIIIIMI11111 Mllllllll M11 C n L HI © Level setting in progress. n n n n u u.u u "'L EL uiitliiifniiiilliilimfifiWiWniiYifli?41 I'ltMIIIMIMIIIIIIIIIIHHIIIIIIIIHHIIHIH 00.00 it o L I “JO *16 -12 -10 -I -4 -JttM *1 »4 +| 0 n n n u.u u “®” indicator illuminates. If the leader tape (attached to each end of recording tape) is reached during the above setting operations, the “ [m] ’’ indicator will rapidly flash on and off to indicate that ATC is not possible. Wind the tape to a position from which ATC can be performed and press the ATC button once again. The display changes as follows while the ATC setting is taking place. Example: Performing ATC on tape deck 2. © Press the ATC button. ‘‘[m]” indicator flashes. Bias setting in progress. n n n n u u.u u W B I ñ S ñU.ilfIIif>TifITIfI r«'i<ñ'
Магнитолы - RS-TR777 (1.19 mb)