Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Fast charger DC1201 Battery cartridge 1201 or 1201A Approx. 60 min. 1200 Approx. 45 min. CAUTION: The fast charger Model DC1201 is specifically designed to charge only Makita battery cartridges. Never use it for other purposes or for other manufacturer's batteries. When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely and recharging a couple of times. If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, the charging light may flash in red color. If this occurs, wait for a while. Charging will begin after the battery cartridge cools. If the charging light flashes alternately in green and red color and a tone sound "beep, beep, beep, ..." for about 20 seconds, a problem exists and charging is not possible. The terminals on the charger or battery cartridge are clogged with dust or the battery cartridge is worn out or damaged. If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Adjusting the stopper plate Loosen the bolts which secure the stopper plate. Adjust the stopper plate in accordance with the screw length as shown in the figure /---Stopper below. Fig. A-I :For screws 25 mm (1 "1 or 28 mm ( 1-118") long Fig. A-2: For screws 32 mm (1 -114") long Fig. A-3: For screws 40 mm (1-9/16") long Then tighten the bolts to secure the stopper plate. L.-----Pins Pin /A I T Fig. A-I Fig. A-2 Fig. A-3 NOTE: As for Fig. A-2 and A-3, secure the stopper plate with both ends contacting the pins on each side to keep the plate from tilting. Adjusting the driving depth Depress the stopper plate as far as it will go. While keeping it in this position, turn the adjusting knob until the bit tip projects approx. 5 mm (3/16")from the stopper plate. Approx. 5 mm (3/16")c Drive a trial screw. If the screw head projects above the surface of the workpiece, turn the adjusting knob in the Wdirection; if the screw head is countersunk, turn the adjust- ing knob in the Bdirection. Casing Stopper plate Adjusting knob Installing the screw strip Insert the screw strip through the screw guide. Then insert it through the feeder box until the first screw reaches the position next to the driving position. Screw guide peder box Driving position Removing the screw strip To remove the screw strip, just pull it out in the direction of the arrow. Carry hook The carry hook is convenient for temporarily hanging the tool. It can be installed on either left or right side of the tool. Hook Switching ON and OFF CAUTl ON: Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. To switch on, press the trigger. Switch trigger To switch off, release the trigger. \ Driving operation Switch on the tool by pressing the trigger. Hold the tool squarely against the workpiece and apply forward pressure to the tool. The screw will be automatically carried to the driving position and driven into the workpiece. CAUTION: Do not fire the tool without screws. This will damage the workpiece. If the feeder box becomes sluggish in operation, spray car wax (spray type wax) on its sliding surfaces. Never lubricate it. Installing or removing the bit CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit. Loosen the bolt which secures the casing. Pull out the casing in the direction of the arrow. Press the dust cover toward the plane bearing and pull out the bit. If the dust cover cannot be moved as far as the plane bearing, try it again after turning the bit slightly. To install the bit, insert it into the socket while turning it slightly. After installing, always make sure that the bit is securely held in place by trying to pull it out. Plane bearing Dust cover 7asing I Hex wrench Screwdriving performance The following reference table indicates the approximate screwdriving capacities from a single charge. It may differ under some condition. 1 Application Thickness of drywall Foundation for drywall Fastenings Battery 1200 Battery 1201 Drywall screw 15/32" x 1") 4.0 mm x 25 mm 12 mm (1 5/32") Steel stud thick 0.5 mm (1/64") Approx. 430 screws Approx. 610 screws Drywall screw 4.0 mm x 40 mm (5/32" x 1-9/16") 18 mm (23/32") Wood or plywood Approx. 230 screws Approx. 330 screws CAUTIO N : If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. MAINTENANCE CAUTl ON: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain pro...
Эта инструкция также подходит к моделям:Дрели и шуропопверты - 6831D (755.98 kb)